Getting Started with Plumbing Basics for Bathtub Installation

Call Today

We have uncovered this article about How to Install a Bathtub: Install an Acrylic Tub and Tub Surround directly below on the internet and think it made sense to share it with you on this site.


How to Install a Bathtub Yourself
Installing a bathtub isn't specifically brain surgery, yet it does need solid plumbing, carpentry, and often, tiling skills. Changing an old bath tub with a new one is additionally a reasonably tough project. If the old tub is easily accessible, the job can move rapidly; if you need to open a wall to get rid of the old tub and also place the new bathtub, the job is much harder. In either case, the task is within a residence handyman's abilities, although you will need a helper to vacate the old bathtub as well as set in the new one. Make sure you have actually qualified on your own for the task as well as fit trying it. As opposed to employing a contractor to take control of a halfway-completed task, it is far better to consider using one before you start. Possibilities are you might require a professional plumber to make tube connections.
This post will certainly help you install a brand-new bathtub in your restroom if you have actually currently bought a new tub as well as do not need to change the setup of your previous water system pipelines.
Your tools and also material checklist should comprise the following:
  • New Tub
  • Hammer

  • Pipeline Wrenches

  • Prybar

  • Shatterproof glass

  • Level

  • Pliers

  • Adjustable Wrench

  • Putty Knife

  • Screwdriver

  • Cold Knife

  • Measuring tape

  • Pipe Caps


  • Preparing for the Setup


    First of all, the sustaining frame supplied with the bath should be fitted (if called for) according to the manufacturer's instructions. Next, fit the taps or mixer to the bath tub. When fitting the tap block, it is essential to make sure that if the faucet comes with a plastic washing machine, it is fitted in between the bath as well as the taps. On a plastic bathroom, it is also reasonable to fit a supporting plate under the taps unit to stop pressure on the tub.
    Fit the adaptable faucet adapters to the bottom of the two faucets making use of 2 nuts and olives (occasionally supplied with the tub). Fit the plug-hole outlet by smearing mastic filler round the sink electrical outlet opening, and afterwards pass the electrical outlet through the hole in the bath. Use the nut provided by the maker to fit the plug-hole. Check out the plug-hole electrical outlet for an inlet on the side for the overflow pipe.
    Next, fit the end of the flexible overflow pipe to the overflow outlet. After that, screw the pipe to the overflow face which need to be fitted inside the bath. Make sure you utilize every one of the supplied washers.
    Attach the trap to the bottom of the waste outlet on the bathtub by winding the thread of the waste electrical outlet with silicone mastic or PTFE tape, as well as screw on the catch to the electrical outlet. Link the bottom of the overflow tube in a comparable manner.The bath ought to now be ready to be suited its final placement.

    Removing Old Touches


    If you require to replace old faucets with brand-new ones as a part of your installation, after that the first thing you need to do is separate the water. After doing so, turn on the taps to drain pipes any kind of water remaining in the system. The process of removing the existing faucets can be rather troublesome because of the restricted accessibility that is typically the instance.
    Use a basin wrench (crowsfoot spanner) or a faucet device to reverse the nut that links the supply pipelines to the faucets. Have a fabric ready for the staying water that will originate from the pipelines. Once the supply pipelines have actually been removed, use the very same device to loosen the nut that holds the taps onto the bath/basin. You will certainly require to quit the single taps from transforming throughout this procedure. When the taps have been removed, the holes in the bath/basin will need to be cleaned up of any kind of old securing substance.
    Before proceeding to fit the brand-new faucets, contrast the pipe links on the old faucets to the new faucets. If the old taps are longer than the new taps, after that a shank adapter is needed for the new taps to fit.

    Setting up the Bath tub


    Making use of the two wood boards under its feet, position the tub in the called for placement. The wood boards are useful in evenly spreading out the weight of the tub over the location of the boards rather than concentrating all the weight onto 4 small factors.
    The following objective is to make certain that the bath tub is leveled all round. This can be accomplished by examining the spirit level as well as adjusting the feet on the bathtub till the level checks out degree.
    To mount faucets, fit all-time low of the furthest adaptable faucet adapter to the ideal supply pipe by making a compression sign up with; then do the very same for the other faucet.
    Activate the water system as well as examine all joints and also brand-new pipework for leaks and also tighten them if needed. Fill up the tub and likewise check the overflow electrical outlet and also the normal electrical outlet for leaks.
    Lastly, repair the bath paneling as described in the maker's instruction manual. Tiling and also sealing around the tub should wait till the bathtub has actually been used a minimum of once as this will settle it into its final placement.

    Fitting New Touches


    If the tails of the new faucets are plastic, after that you will require a plastic adapter to avoid damages to the string. One end of the port fits on the plastic tail of the tap and also the other end supplies a link to the existent supply pipes.
    If you need to fit a monobloc, then you will require minimizing couplers, which links the 10mm pipe of the monobloc to the conventional 15mm supply pipe.
    Next off, position the tap in the installing opening in the bath/basin making sure that the washers remain in area in between the tap and the sink. Protect the faucet in place with the maker given backnut. When the faucet is securely in place, the supply pipelines can be connected to the tails of the taps. The taps can either be linked by using corrugated copper piping or with regular tap adapters. The former kind should be linked to the tap ends first, tightening just by hand. The supply pipelines can later on be linked to the other end. Tighten up both ends with a spanner after both ends have been attached.

    Tiling Around the Bathtub


    In the area where the bathroom meets the floor tile, it is necessary to seal the accompanies a silicone rubber caulking. This is important as the installation can relocate enough to fracture an inflexible seal, creating the water to pass through the wall in between the bath and also the tiling, bring about problems with dampness and feasible leaks to the ceiling below.
    You can pick from a range of coloured sealants to blend in your fixtures and installations. They are sold in tubes and also cartridges, and are capable of sealing spaces up to a width of 3mm (1/8 inch). If you have a larger gap to fill, you can load it with twists of soaked paper or soft rope. Bear in mind to constantly fill up the bath tub with water prior to securing, to allow for the motion experienced when the bathtub is in use. The sealant can break relatively early if you do not consider this activity prior to sealing.
    Alternatively, ceramic coving or quadrant floor tiles can be used to border the bathroom or shower tray. Plastic strips of coving, which are easy to use and cut to dimension, are also easily readily available on the marketplace. It is suggested to fit the ceramic tiles making use of water-resistant or water resistant glue and grout.

    Bathtub Installation


    How Important Is A Bathtub To Your Home?


    High-quality baths, showers, and other bathroom updates are necessary when considering a smart investment in your home. It’s a room that you go to every day and one that is constantly being used by guests.The bathroom is one of the top trafficked rooms in a home and also one of the most valuable in terms of home resale.


    Install Piping Before Tub


    You will be using your existing drain and waste vent system, but pipes required include the hot and cold water supply lines and a pipe leading to a shower head. A mixing valve and shower head are also needed. Air chambers may be required.


    Position the Tub


    Lower the tub into place so that the continuous flange fits against the wall studs and rests on 1’x4' or 2’x4' supports. Anchor the tub to the enclosure with nails or screws inserted through the flanges into the studs.



    NOTE: Remember, bathtubs and shower stalls may require support framing. A bathtub filled with water is extremely heavy, so check building codes and framing support before installing the tub.


    Assemble Drain Connections


    Assemble the bathtub drain connections by connecting the tub overflow with the tub drain above the trap, not beyond it. The trap will have a compression fitting that screws over the arm of the overflow assembly.


    Place a Pipe For the Shower Head


    First, locate a brass female threaded winged fitting and attach it to a framing support via a screw or a nail. Then run a pipe up the wall for the shower head. Sweat or solder the other side of the brass fitting to the top of the pipe.


    Attaching Hot and Cold Water Lines


    Attach your water lines for both hot and cold by sweating these directly into the hot and cold ports of the mixing valve. The mixing valve will be how water enters the tub’s system, not by the pipes themselves.


    Install the Spout


    Extend a piece of 1/2 inch pipe, or whichever length is specified in the manufacturer’s instructions, for the tub spout. Sweat on a male threaded fitting at the end of the pipe or use a brass nipple of the proper length and a 1/2 inch cap.



    NOTE: At this point you should have your rough-in plumbing work inspected before proceeding further.


    Check For Leaks


    Restore the water pressure and check the drain connection and the supply pipes for any sign of leaking.


    estore the Bathroom Wall


    Replace the wall with moisture-resistant drywall as a base for your wall covering. Seal the joints between the wall and your new tub with silicone caulk as protection against water seepage.

    https://www.berkeys.com/2016/12/02/bathtub-installation-dallas/


    Installing A Bathtub

    I discovered that review on How to Install a Bathtub while perusing the search engines. Appreciated our entry? Please share it. Let other people check it out. I enjoy reading our article about A Step-by-Step Guide to Installing a Bathtub.


    Always here, call!

    Leave a Reply

    Your email address will not be published. Required fields are marked *